smartctl 7.3 2022-02-28 r5338 [FreeBSD 13.1-RELEASE amd64] (local build)
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Samsung SpinPoint M8 (AF)
Device Model:     ST500LM012 HN-M500MBB
Serial Number:    --
LU WWN Device Id: 5 0004cf ...
Firmware Version: 2AR10002
User Capacity:    500,107,862,016 bytes [500 GB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5400 rpm
Form Factor:      2.5 inches
Device is:        In smartctl database 7.3/5319
ATA Version is:   ACS-2, ATA8-ACS T13/1699-D revision 6
SATA Version is:  SATA 2.6, 3.0 Gb/s
Local Time is:    Mon Jun 27 07:52:39 2022 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM feature is:   Disabled
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		( 6360) seconds.
Offline data collection
capabilities: 			 (0x51) SMART execute Offline immediate.
					No Auto Offline data collection support.
					Suspend Offline collection upon new
					command.
					No Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 106) minutes.
SCT capabilities: 	       (0x003d)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR-K   100   100   051    -    5486
  2 Throughput_Performance  POS--K   055   039   000    -    5915
  3 Spin_Up_Time            PO---K   091   090   025    -    2867
  4 Start_Stop_Count        -O--CK   088   088   000    -    12685
  5 Reallocated_Sector_Ct   PO--CK   252   252   010    -    0
  7 Seek_Error_Rate         POSR-K   252   252   051    -    0
  8 Seek_Time_Performance   P-S--K   252   252   015    -    0
  9 Power_On_Hours          -O--CK   100   100   000    -    21778
 10 Spin_Retry_Count        PO--CK   252   252   051    -    0
 11 Calibration_Retry_Count -O--CK   098   098   000    -    2343
 12 Power_Cycle_Count       -O--CK   090   090   000    -    11017
181 Program_Fail_Cnt_Total  -O---K   096   096   000    -    87602630
183 Runtime_Bad_Block       -O--CK   100   100   010    -    4
184 End-to-End_Error        PO--CK   252   252   048    -    0
186 Unknown_Attribute       -O--CK   252   252   000    -    0
187 Reported_Uncorrect      -O--CK   100   100   000    -    2006
188 Command_Timeout         -O--CK   252   252   000    -    0
190 Airflow_Temperature_Cel -O----   061   035   040    Past 39 (Min/Max 0/66)
191 G-Sense_Error_Rate      -O---K   100   100   000    -    1307
192 Power-Off_Retract_Count -O---K   252   252   000    -    0
193 Load_Cycle_Count        -O--CK   064   064   000    -    365164
194 Temperature_Celsius     -O----   061   035   000    -    39 (Min/Max 0/66)
195 Hardware_ECC_Recovered  -O-RCK   100   100   000    -    0
196 Reallocated_Event_Count -O--CK   252   252   000    -    0
197 Current_Pending_Sector  -O--CK   252   100   000    -    0
198 Offline_Uncorrectable   ----CK   252   252   000    -    0
199 UDMA_CRC_Error_Count    -OS-CK   098   098   000    -    1344
200 Multi_Zone_Error_Rate   -O-R-K   001   001   000    -    605774
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      2  Comprehensive SMART error log
0x03       GPL     R/O      2  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      2  Extended self-test log
0x08       GPL     R/O      2  Power Conditions log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xc0-0xdf  GPL,SL  VS      16  Device vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Device Error Count: 2931 (device log contains only the most recent 8 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 2931 [2] occurred at disk power-on lifetime: 18437 hours (768 days + 5 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 00 08 00 00 2b 92 60 00 e0 00  Error: ICRC, ABRT 8 sectors at LBA = 0x2b926000 = 731013120

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 08 00 00 2b 92 60 00 e0 08     00:00:01.884  READ DMA EXT
  25 00 00 01 f8 00 00 27 52 5a 08 e0 08     00:00:01.884  READ DMA EXT
  25 00 00 00 08 00 00 1a db 08 10 e0 08     00:00:01.884  READ DMA EXT
  25 00 00 00 08 00 00 39 da 9f f0 e0 08     00:00:01.884  READ DMA EXT
  25 00 00 00 08 00 00 39 da a8 08 e0 08     00:00:01.884  READ DMA EXT

Error 2930 [1] occurred at disk power-on lifetime: 18437 hours (768 days + 5 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 00 30 00 00 39 da a8 48 e0 00  Error: ICRC, ABRT 48 sectors at LBA = 0x39daa848 = 970631240

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 30 00 00 39 da a8 48 e0 08     00:00:01.875  READ DMA EXT
  25 00 00 00 08 00 00 27 52 58 18 e0 08     00:00:01.875  READ DMA EXT
  25 00 00 00 08 00 00 1a db 08 00 e0 08     00:00:01.875  READ DMA EXT
  25 00 00 00 08 00 00 27 52 78 00 e0 08     00:00:01.875  READ DMA EXT
  25 00 00 00 10 00 00 39 da a8 28 e0 08     00:00:01.875  READ DMA EXT

Error 2929 [0] occurred at disk power-on lifetime: 18437 hours (768 days + 5 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 00 40 00 00 2b 27 6b 80 40 00  Error: ICRC, ABRT 64 sectors at LBA = 0x2b276b80 = 724003712

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 40 00 00 2b 27 6b 80 40 00     00:00:01.825  READ DMA EXT
  25 00 00 00 40 00 00 2b 27 6b 40 40 00     00:00:01.825  READ DMA EXT
  25 00 00 00 40 00 00 2b 27 6b 00 40 00     00:00:01.825  READ DMA EXT
  25 00 00 00 40 00 00 2b 27 6a c0 40 00     00:00:01.825  READ DMA EXT
  25 00 00 00 40 00 00 2b 27 6a 80 40 00     00:00:01.825  READ DMA EXT

Error 2928 [7] occurred at disk power-on lifetime: 18437 hours (768 days + 5 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 00 40 00 00 2b 27 41 80 40 00  Error: ICRC, ABRT 64 sectors at LBA = 0x2b274180 = 723992960

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 40 00 00 2b 27 41 80 40 00     00:00:01.824  READ DMA EXT
  25 00 00 00 40 00 00 2b 27 41 40 40 00     00:00:01.824  READ DMA EXT
  25 00 00 00 40 00 00 2b 27 41 00 40 00     00:00:01.824  READ DMA EXT
  25 00 00 00 40 00 00 2b 27 40 c0 40 00     00:00:01.824  READ DMA EXT
  25 00 00 00 40 00 00 2b 27 40 80 40 00     00:00:01.824  READ DMA EXT

Error 2927 [6] occurred at disk power-on lifetime: 18437 hours (768 days + 5 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 01 d1 00 00 29 13 9d af 40 00  Error: ICRC, ABRT 465 sectors at LBA = 0x29139daf = 689151407

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  35 00 00 04 40 00 00 29 13 9b 40 40 00     00:00:01.607  WRITE DMA EXT
  35 00 00 00 40 00 00 29 13 9b 00 40 00     00:00:01.607  WRITE DMA EXT
  35 00 00 02 40 00 00 29 13 98 80 40 00     00:00:01.607  WRITE DMA EXT
  35 00 00 00 40 00 00 29 13 95 80 40 00     00:00:01.607  WRITE DMA EXT
  35 00 00 06 00 00 00 29 13 8f 40 40 00     00:00:01.607  WRITE DMA EXT

Error 2926 [5] occurred at disk power-on lifetime: 18437 hours (768 days + 5 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 00 40 00 00 29 8f 69 80 40 00  Error: ICRC, ABRT 64 sectors at LBA = 0x298f6980 = 697264512

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 40 00 00 29 8f 69 80 40 00     00:00:01.573  READ DMA EXT
  35 00 00 00 40 00 00 29 76 31 80 40 00     00:00:01.573  WRITE DMA EXT
  35 00 00 00 40 00 00 29 76 2f c0 40 00     00:00:01.573  WRITE DMA EXT
  35 00 00 00 40 00 00 29 76 2f 80 40 00     00:00:01.573  WRITE DMA EXT
  35 00 00 00 40 00 00 29 76 2f 40 40 00     00:00:01.573  WRITE DMA EXT

Error 2925 [4] occurred at disk power-on lifetime: 18437 hours (768 days + 5 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 00 40 00 00 2b 0f a7 80 40 00  Error: ICRC, ABRT 64 sectors at LBA = 0x2b0fa780 = 722446208

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 40 00 00 2b 0f a7 80 40 00     00:00:01.555  READ DMA EXT
  25 00 00 00 40 00 00 29 3d 4a 00 40 00     00:00:01.555  READ DMA EXT
  25 00 00 00 40 00 00 2b 0f b0 c0 40 00     00:00:01.555  READ DMA EXT
  25 00 00 00 40 00 00 28 ed 34 c0 40 00     00:00:01.555  READ DMA EXT
  25 00 00 00 40 00 00 2b 0f c0 40 40 00     00:00:01.555  READ DMA EXT

Error 2924 [3] occurred at disk power-on lifetime: 18437 hours (768 days + 5 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 00 40 00 00 2b 7b be 80 40 00  Error: ICRC, ABRT 64 sectors at LBA = 0x2b7bbe80 = 729529984

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 40 00 00 2b 7b be 80 40 00     00:00:01.554  READ DMA EXT
  25 00 00 00 40 00 00 2b 7b ab 40 40 00     00:00:01.554  READ DMA EXT
  25 00 00 00 40 00 00 2b 7b af c0 40 00     00:00:01.554  READ DMA EXT
  25 00 00 00 40 00 00 2b 7b b5 40 40 00     00:00:01.554  READ DMA EXT
  35 00 00 00 40 00 00 29 14 5e c0 40 00     00:00:01.554  WRITE DMA EXT

SMART Extended Self-test Log Version: 1 (2 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%     21719         -
# 2  Short offline       Completed without error       00%     21715         -
# 3  Short offline       Completed without error       00%     21699         -
# 4  Short offline       Completed without error       00%     21685         -
# 5  Short offline       Completed without error       00%     21674         -
# 6  Short offline       Completed without error       00%     21660         -
# 7  Short offline       Completed without error       00%     21651         -
# 8  Short offline       Completed without error       00%     21640         -
# 9  Short offline       Completed without error       00%     21630         -
#10  Short offline       Completed without error       00%     21613         -
#11  Short offline       Completed without error       00%     21601         -
#12  Short offline       Completed without error       00%     21584         -
#13  Short offline       Completed without error       00%     21573         -
#14  Short offline       Completed without error       00%     21563         -
#15  Extended offline    Completed without error       00%     21557         -
#16  Short offline       Completed without error       00%     21458         -
#17  Short offline       Completed without error       00%     21458         -
#18  Short offline       Completed without error       00%     21370         -
#19  Short offline       Completed without error       00%     21352         -
#20  Extended offline    Aborted by host               30%     21342         -
#21  Extended offline    Aborted by host               40%     19882         -

SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Completed [00% left] (0-65535)
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  2
SCT Version (vendor specific):       256 (0x0100)
Device State:                        Active (0)
Current Temperature:                    39 Celsius
Power Cycle Min/Max Temperature:     22/47 Celsius
Lifetime    Min/Max Temperature:      6/66 Celsius
Specified Max Operating Temperature:    80 Celsius
Under/Over Temperature Limit Count:   0/0

SCT Temperature History Version:     2
Temperature Sampling Period:         5 minutes
Temperature Logging Interval:        5 minutes
Min/Max recommended Temperature:     -5/80 Celsius
Min/Max Temperature Limit:           -10/85 Celsius
Temperature History Size (Index):    128 (86)

SCT Error Recovery Control:
           Read:     85 (8.5 seconds)
          Write:     85 (8.5 seconds)

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  4            0  Command failed due to ICRC error
0x0002  4            0  R_ERR response for data FIS
0x0003  4            0  R_ERR response for device-to-host data FIS
0x0004  4            0  R_ERR response for host-to-device data FIS
0x0005  4            0  R_ERR response for non-data FIS
0x0006  4            0  R_ERR response for device-to-host non-data FIS
0x0007  4            0  R_ERR response for host-to-device non-data FIS
0x0008  4            0  Device-to-host non-data FIS retries
0x0009  4            4  Transition from drive PhyRdy to drive PhyNRdy
0x000a  4            3  Device-to-host register FISes sent due to a COMRESET
0x000b  4            0  CRC errors within host-to-device FIS
0x000d  4            0  Non-CRC errors within host-to-device FIS
0x000f  4            0  R_ERR response for host-to-device data FIS, CRC
0x0010  4            0  R_ERR response for host-to-device data FIS, non-CRC
0x0012  4            0  R_ERR response for host-to-device non-data FIS, CRC
0x0013  4            0  R_ERR response for host-to-device non-data FIS, non-CRC
0x8e00  4            0  Vendor specific
0x8e01  4            0  Vendor specific
0x8e02  4            0  Vendor specific
0x8e03  4            0  Vendor specific
0x8e04  4            0  Vendor specific
0x8e05  4            0  Vendor specific
0x8e06  4            0  Vendor specific
0x8e07  4            0  Vendor specific
0x8e08  4            0  Vendor specific
0x8e09  4            0  Vendor specific
0x8e0a  4            0  Vendor specific
0x8e0b  4            0  Vendor specific
0x8e0c  4            0  Vendor specific
0x8e0d  4            0  Vendor specific
0x8e0e  4            0  Vendor specific
0x8e0f  4            0  Vendor specific
0x8e10  4            0  Vendor specific
0x8e11  4            0  Vendor specific

